Grade 12 results are out. Where to check yours

Grade 10 Physics unit 4

What decides a wire's resistance

4 min · 2 past exam questions worked through

Parts of the lesson

Tap a part to play the lesson from there.

A 4-minute Temari video lesson on Grade 10 Physics unit 4: What decides a wire's resistance. It works through 2 past exam questions step by step.

More on unit 4

The chapter's own page holds the rest of what Temari has on it, such as short notes and practice questions with their answers.

Open the unit 4 page

Everything the lesson says

The lesson's words, part by part. Tap a time to play the lesson from there.

0:00Introduction

Some wires let current through easily. Others hold it back. Today you will learn the three things that decide a wire's resistance, and the one formula that puts them together.

0:12Resistance

When a potential difference V drives a current I through a metal wire, V divided by I stays the same. That constant is the resistance of the wire, R. This is Ohm's law: V equals I times R. Resistance is measured in ohms.

So for the same voltage, a wire with more resistance lets less current through.

0:37Length and thickness

Resistance depends on three things. First, the length of the wire. A longer wire has more resistance: R is proportional to the length, L.

Second, the cross-sectional area, A. That is the face you would see if you cut the wire straight across. Current flows easily through a thick wire, and hardly through a thin one. So R is inversely proportional to A.

1:04The material, and the formula

Third, the material. Each material has its own resistivity, written with the Greek letter rho. Good conductors have very low resistivity. Good insulators have very high resistivity.

Put all three together, and R equals rho times L, over A. Longer means more. Thicker means less. And the material sets rho.

1:31Exam question 1Past exam

Now a real exam question, from the 2018 Grade 12 national exam. It tests this Grade 10 chapter. Which formula correctly expresses the resistivity of a resistor with resistance R, length L, and cross-sectional area A? Pause the video, and try it.

Start from R equals rho L over A. Multiply both sides by A: R A equals rho L. Now divide both sides by L: rho equals R A over L. The answer is C. B is the trap: it swaps L and A. Option A puts R at the bottom, upside down. And D just multiplies all three.

2:19When the wire changes

Exam questions love to change the wire. You do not need rho, and you do not need its value. Write the formula, and put each change in as a factor.

Double the length, and a two goes on top: R doubles. Double the area, and a two goes on the bottom: R halves. Do both at once, and the two twos cancel. The resistance stays the same.

2:46Exam question 2Past exam

One more, from the 2017 national exam. A wire with a resistance of six ohms is drawn out into a new wire, two times as long as the original, with half the cross-sectional area. What is the resistance of the new wire? Pause, and try it.

Length times two puts a two on top. Area times a half puts a half at the bottom, and dividing by a half doubles R again. Two times two is four. Four times six ohms is twenty four ohms. The answer is D. A, twelve ohms, is the trap: it counts only one of the two changes. C, three ohms, makes R smaller, when it should grow. And B forgets that the wire changed at all.

3:38Summary

So remember. Resistance is V over I, measured in ohms. A longer wire has more resistance, and a thicker wire has less. And R equals rho L over A, where rho belongs to the material. Keep practising questions like these on Temari.et.

Practise this unit in the app

Temari turns this chapter into timed practice and marks it as you go, with an AI tutor to explain anything that did not land.

Start free

Temari.et is also an Android app, free on Google Play.

Sign inCreate your account